This is a brand new BOSS TRIPLE air bag load assist kit along with the PX-01 In Cab Compressor to suit the rear of the Ford F250 and F350 models from 2010 onwards that have a 3" to 6" lift.
Suits vehicles that have a 3" to 6" suspension lift.
This kit includes our triple convoluted bags (Part #2503) for vehicles with extra lift like 3" to 6". They can hold your car at a given height with less air pressure than that of the double bags so it means for a softer ride. But note they take up more room so are not suitable for standard to 2" lifted vehicles.
Some pictures in this listing show double bags - that's so you can see the brackets and how they work. This package deal is for the TRIPLE bags and the PX-01 In Cab Compressor.
This is our new improved design. It utilises our heavier 2600 bags and is designed so the van rides at normal heights. Other brands are the same as our old model and when effective the van runs 2" taller in the rear. But not this kit - you still run at normal heights and still benefit from the bags being able to carry loads of 2t or more. The Load Assist Kit comes with:
- 2 x BOSS Extreme Series Triple Bellow Airbags
- 4 x brackets (2 upper & 2 lower)
- Mounting Hardware
- Quality SAE J844 Government Approved Airline
- Dual Schrader Valves Mounted in Stainless Panel
- Instructions for fitting
Boss Extreme series airbags are rated at 2600lb or 1136kg per side and have been government approved tested to over 750psi.
All Boss airbags are manufactured by us and are branded Boss. Beware of unbranded airbags, usually coming from China from other companies.
Average dual cab ute will run around 15-45psi depending on load.
Boss has sold over 13000 load assist kits in Australia, proven over time with 4WD enthusiasts, Mining companies, Tradies, 4WD Tour Operators as well as in Agricultural Vehicles, Trailers and motorhomes, limited only to your imagination.
To get the best performance from your kit inflate airbags just enough to achieve a level ride height. By doing this you are also allowing all of the suspension components to share the extra load of the vehicle and not putting any unecessary pressure on any one individual part of your vehicles suspension.
This kit is used to control Load Assist Kits from inside your cab without the need for a tank and electric valves.
Simple installation and controls bags independently up and down using our PX-01 compressor
- 1 x PX-01 12V BOSS Air Compressor.
- 1 x Stamped stainless steel gauge panel.
- 2 x Pneumatic Push Buttons for dropping each bag.
- 1 x 12V momentary switch for compressor.
- 1 x BOSS 200psi Dual Needle back-lit Gauge.
- 10 meters of 1/4” J844 DOT Airbrake line.
- 2 x 1/4” push connect check valves.
- 3 x Y Connectors.
- 2 x T Connectors.
- 4 x 1/4” female push fittings for gauge and buttons.
- 10 x Cable Ties.
- Instruction Sheet.
The In Cab kit includes the BOSS PX01 Compressor, gauge and controls. When you turn on the compressor it pumps up the 2 air bags. It includes one way valves which prevent air transferring from one bag to the other and that makes for a better ride. Also includes a gauge with twin needles and it includes a manual dump valve for letting down each bag separately.
This Kit can be run with little or no air for no load or fully inflated for heavy loads. No drilling, welding or cutting is needed. The rubber is a heavier grade than your tyres and individual components are all replacable.
All Boss Kits come with a full 5 year warranty, regardless of which vehicle it is in or who fits the Kit.
SAVE TIME AND MONEY WITH THIS ALL-IN-ONE TRIPLE AIR BAG LOAD ASSIST KIT & PX-01 COMPRESSOR (IN CAB KIT)